Product Name:280Kg Single Door Magnetic Lock
Usage:Access control system output for external devices , suction force generated by DC12V voltage path and is widely used in all kinds of doors tools, suitable for installation in steel doors, fire doors , doors , etc.
280kg (600Lbs) static linear tension
Factory set to 12VDC voltage standard
Built-in reverse current protection device (MOV)
Suitable for wooden doors, glass doors, metal doors, fire doors
Anti residual magnetism design, selection of materials imported iron
The shell is made of high-strength aluminum alloy, Anodized
Magnetic locks no mechanical failure, complete with electromagnetic suction work
Increase the electromagnetic suction , professional design, insulated double lock
Products certified by China MA
Product parameters :
Lock Size : Length Width 250x height 48x 25 (mm)
Blister Dimensions: Length Width 180x height 38x 11 (mm)
Maximum tension : 280kg (600Lbs) straight Rally
Input voltage : DC12V
Current : 12V/450mA
Applicable : Wooden door , glass doors, metal doors, fire doors
Surface temperature: +20 ° below ambient temperature within
Temperature : -10 ~ +55 ° (14-131F)
Suitable Humidity : 0 ~ 95% ( relative humidity )
Shell: Anodized aluminum
Lock handle : Environmental plating
Blister Treatment: environmental plating
Weight : 2kg
One . The outer surface of the door installation method :(See Charts 1 to eight )
Step One: First, open the cover with a screwdriver , hex wrench and then hit the side plate , ready to install(See Figure 1 )
Step two: take out the installation of cardboard , paperboard folded along the dotted line by the method shown in Figure Two locks on the cardboard into the desired position,Then place the needed punch after punch mark cook .
The third step:
A.Following iron fixed ( see Figure III )
Following the hex screws into the iron , and the rubber washer between the home and the two pieces of metal washer, and then set the inner hexagon screws. The following three holes to play on the iron door of the insert , while the mushroom from the other side of the door inserts, hex wrench will continue to use the iron lock on the door.
B. Fixed side panels (see Figure III ) to the side plate with two round head screws on the door frame in the previous drilling (fixed elongated hole in the side of the plate ) . Note: Do not lock the side panels , to allow it to be able to move back and forth in order to facilitate safe location fix .C. Position correction side plate side plate and continue to make the location suitable for iron , the main purpose of the lock with the following iron close contact .D: After fixing the lock body side panels and the side panels of the locking button head screws , countersunk head and then lock all the screws , and then remove the button head screws , drill holes in the proper position for wiring. Finally, Allen wrench to lock the main lock on the side panel .(See Figure IV)
Step Four : Follow the instructions manual wiring.
Step Five: Close the lid , put a small aluminum cylinder into the lock body see Figure VThe screw holes. See Figure VI
Figure VII and Figure eight shows a typical installation of external outer door design
Second, the inner surface of the door mounting(ZLInstallation type bracket ) : problem solving interior exterior magnetic locks.
Accessories needed when installing the inner surface of the door to help make the installation , we use the rich decorative quality imported aluminum to making this installation accessories :Z \u0026 LBracket. EachZ \u0026 LBracket with three aluminum parts,Where the longer oneL1Lock the main use is rationed;Another two shorterZ2,Z3Following the iron rations used .Z2Is mounted on the door , the edge of a sink five holes for fixing to the door;Z3Following is an iron plate for fixing,There are three holes on the edge,Following the center hole should be aligned with the center hole iron.The following describes the installation method.
a.FirstZ \u0026 LThe bracketL1Bracket mounted on the lock position, withM5 * 25The self-tapping screws on the door frame or wall .
b. Lock body with a hex wrench to lock inL1Bracket.
c.Corresponds toL1The position of the carriageZ2Bracket on the door.
d.Will continue to iron insertZ1The three holes fixed false,Then the door closed , the magnet and iron closely following the match, to determineZ1,Z2Convergence position. (Z1VersusZ2The relative position can be adjusted according to the thickness of the door ) .
e.WillZ1,Z2Lock , and then continue with ironM8 * 25Hexagon screws onZ1On ( screws , iron , gaskets , rubber gaskets in order penetration ) .
f.If the double doors , you can use twoZ \u0026 LStand
Third, embedded ( built-in ) installation method :
Consistent with the outer door open embedded installation method
For doors , if the size of the door wall , then buried the body enough locks , installation is very simple, just dig a proper slot , the lock screw to lock buried , general construction workers will see the lock installed . Aluminum door frames are generally hollow, for this feature , we designed two installation methods.
A. Lined block method ( refer to Figure X. Figure XI ) : placed in a door frame in the right size timber for lining , and then lock the screws. This method is easily obtained, easy to install. Most of the actual installation using this method .
B. Use mounting accessories method : This method is the use of accessories we offer ( four holes iron+ UType iron ) , making installation easier.
Fourth, the glass door installation method :
A.There are aluminum ( or other material ) Installation package framed glass doors
Installation method and ordinary door flush mounted the same.
Glass doors need to pack boxes containing aluminum , due to lock suction and distance requirements of less than6Mm , it requires a distance smaller than the door to the door frame6Mm, the spring requires the use of stable quality , otherwise it will affect the lock position.
Two.Frameless glass door installation method
Generally difficult to install locks on the glass door , even though some locks can be installed , but it will affect the appearance of the whole door , and our single greatest heart with electromagnetic lock installation accessories , you can easily install, reliable and aesthetically pleasing .
1 .UseUBracket installed magnetic locks on the frameless glass door :
Framed glass door did not need accessories to aid installation. Installation method and the method of ordinary door surface mount basic similarity , but is installed in the third step , following the iron when the different installation methods as shown in Figure 9 .TheUGroove together with rubber cushion and stainless steel gasket ( on the lock screw side ) set in the glass door,No head screw with the lock on the glass door,Then following the fixed ironUGroove on . For different glass door thickness and different types of electromagnetic locks, we offer different types of installation accessories :U-Stand, Specifications, please see table below:
2 .UseABRack to installFirstABFrame fixed with glass adhesive ( or double-sided tape ) on the glass door , then put on the stand following the iron fixed .
*** Welcome visit our officlal website www.security-warehouse.com for most up-to-date product information, manual and software download, knowledge sharing and industrial news. SECURITY-WAREHOUSE.COM is committed to provide professionalism to maximize our clients purchase satisfaction. ***
Magnetic Door Installation Notes:
Please read the installation instructions carefully before installation , and please note the following:
Do not drill holes in the following iron or lock body ; do not replace Following iron screws ; Do not wipe electromagnetic lock with harsh detergents ; do not change the circuit .
Magnetic locks maintenance:
Magnetic locks Locks maintenance and other relatively simple compared to just keep following the main surface of the iron and locks can be free of impurities , so please periodically wipe the surface with a non- eclipse cleaners
* required fields
Block 4 West, SEG Technology Park, Hua Qiang Road North, Shenzhen, China