Welcome visit RFID & Security Warehouse!

Category Navigation:

ID card access control access control single door access control access control system 500 users

$4.66

Availability: In stock

Be the first to review this product

ID card access control / access control / single door access control / access control system ( 500 users )
Model : 1729867703

Details

1 .             Technical Parameters:

 

Project

Index

Power Supply

Direct-current12VDC+10% ; Current1.2A

Unlock Relay

DC 12VDC/2A

Ambient temperature

Work:0°~45°; Storage:-10°~55°

Effective storage capacity of the card

500Sheets, each valid card along with a \" personal password \"

Reader transmitting frequency

125HKz

Proximity card identification

EM or EM compatible card

Read Range

5-15CM

Open the door

Cards, universal password

 

2 . Functions and settings: ( Any settings for the controller must be in the programming state )

1) . Enter the programming mode:

Press [*] + [ 6 programming code ] , two beep sound ( red light flashes green light . Factory programming password990101, After enabling users to access the device , be sure to modify the programming code . If the20Within seconds, without any programming instructions , the system automatically exits the programming mode . )

2) . Modify Programming Password:

Press [0] + [6Bit new programming code ] + [ repeat6Bit new programming code ] , toot two sounds ; said set successfully.

3) Is set to open the door :

 .Card or Common Password: press[ 1 ] + [ 0 ], Toot two sounds ;

 ②.Calgary personal password :Press[ 1 ] + [ 1 ], Toot two sounds ;

4) Set opening hours :

 Press[2] + [TT], Toot two sounds ;TTSaid open time , in seconds , such as unlocking time3Sec,TT = 03;

5) Set/Modify global open Password:

 Press[ 3 ] + [ 4Bit of new generic password to open the door], Toot two sound, original4Bit universal password is covered ; Press[ 3 ] + [ 0000 ], Toot two sounds , clear all \"universal password \" ;

6) Set Tamper Alarm function:

 ①.Close Tamper alarm : Press[ 4 ] + [ 0 ], Toot two sounds ;

 ②.Open Tamper alarm : Press[ 4 ] + [ 1 ], Toot two sounds ;

7) Set the effective user ( card ) :

 Press[ 5 ] + [ 3Users number]After two beep sound+ [Then on the controller card], After a sound beep , beep two sounds , carboplatin success ; ( Note :3Bit user ID must be000-500Any number between each card numbers should not be repeated. Specifies the user ID after continuous swipe , added after the user ID you specify will be the starting user number continued to push )

8)Delete valid card :

 ①.Press[ 6 ] + [ 3Users number], Toot two sounds ,

 ②.Press[ 7 ] + [Sensing the need to remove the card], After a sound beep , beep two sounds ; ( delete more cards repeat the above steps )

    Note: To delete all users, proposes to restore the factory settings ;

9) Set Magnetic alarm status :

 ①.Close door sensor alarm : Press[ 8 ] + [ 0 ], Toot two sounds ;

 ②.Open the door sensor alarm : Press[ 8 ] + [ 1 ], Toot two sounds ; ( this feature is turned on , when the normal door is not closed , or did not pass the controller is turned on, the controller will beep beep continuously sounding alarm , external alarm . )

10) To restore the factory settings:

 Press[ 8 ] + [ 6 ], Two audible beep , beep beep followed by three long sound,5After three seconds, toot toot short beeps and returns to normal mode ;

11) To exit the programming mode :

 Press[ * ], Toot two sounds. ( Note :If the20No programming operation, the system automatically exits the programming mode within seconds. )

3. Forced to restore factory programmed password :

 Remove the controller,J2After about two feet short of the release ( energized ) , the controller of a sound beep , followed by two beep sounds , the controller can be restored to the factory programmed password990101

*** Welcome visit our officlal website www.security-warehouse.com for most up-to-date product information, manual and software download, knowledge sharing and industrial news. SECURITY-WAREHOUSE.COM is committed to provide professionalism to maximize our clients purchase satisfaction. ***

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Write Your Own Review

You're reviewing: ID card access control access control single door access control access control system 500 users

Do You Have Any Question ?

8 + 5 = enter the result ex:(3 + 2 = 5)

* required fields

Contact Us

Block 4 West, SEG Technology Park, Hua Qiang Road North, Shenzhen, China

 +86-755-3324-1960

 +1-347-448-4457

Email Newsletters
Welcome leave us your email address for product update